Tamper detection

Tamper detection monitoring, so your coverage cannot be quietly switched off

A vape, smoke or safety sensor only protects a space while it works. When someone covers it, pulls it down or strikes it, the tamper alert goes straight to the Sirix command center, and a live operator responds on your SOP, 24/7, with or without cameras.

Tamper detection monitoring connects the tamper alerts built into sensors and security devices to a 24/7 command center. When a sensor is covered, moved, struck or disconnected, a live Sirix operator receives the alert and responds on the site’s protocol, with or without cameras or speakers.

A hand pressing plastic wrap over a camera-free ceiling sensor, with a tamper alert for Restroom 2

See it for yourself

Try to tamper with a sensor. See what happens next.

Pick what someone might do to a sensor, set up your site, and follow the alert from the ceiling to a live operator.

Best with sound on
Try it: pick an action below
1 Restroom 2Ceiling sensor
2
Standing byRestroom 2 sensor online
Live operator
Sirix command center24/7
4
Your designated contactSensor back in service
Pick an action
depending on the model
Your site
Cameras on site?
Speakers on site?
What happens, step by step
  1. 1
    Tampering

    Pick an action to begin.

  2. 2
    Alert taken

    The alert reaches the Sirix command center. A live operator takes it.

  3. 3
    Response

    The operator opens the nearest camera and sees what is happening.

    The operator speaks through the speaker in the restroom: “This area is monitored. Step away from the device now.”

    The hallway camera shows who leaves the restroom.

    No camera, no speaker. The operator acts on your SOP right away.

    Following your SOP, the operator calls the right people: keyholders, the building manager, guards or police.

    The operator notifies your designated contact to check the sensor and put it back in service.

  4. 4
    Restored

    Coverage restored, not just reported. The event is documented.

In short: a tamper alert on its own sounds a siren and sends a text that can go unread for hours. With Sirix tamper detection monitoring, the alert reaches a live operator 24/7, who checks cameras if you have them, speaks through speakers if you have them, follows your SOP either way, and makes sure the sensor is put back in service.

Detect. Alert. Respond.

How does tamper detection work?

Many modern sensors also watch themselves. Alongside what they are installed to detect, such as vaping, smoke or aggression, built-in tamper detection notices when the device is touched, moved or blocked.

Covered or blocked

When someone tapes over the sensor, wraps it in plastic or puts a bag over it, the sensor notices it can no longer read the room and raises a tamper alert.

Moved or removed

An internal motion sensor knows the device's normal position. If it is turned, pulled off the ceiling or taken down from the wall, the alert fires.

Struck or shaken

A hit with an object, a kick or a hard knock registers as an impact. Many models also sound a loud alarm on the spot to discourage the person.

Close-up of a white ceiling sensor wrapped in plastic film to block it

What tamper detection can flag

Blocking

Physical handling

Connection

Manufacturer reported: tamper detection types vary by sensor model and are confirmed during your site assessment. Pair it with vape detection to know what someone was trying to hide.

The Sirix layer

The sensor knows it was touched. A live operator acts on it.

A tamper alert on its own sounds a siren and sends a text. It cannot check who is there, speak to them or make sure the sensor works again. Sirix connects any sensor to its 24/7 command center, and a trained, bilingual operator takes every tamper alert and follows your SOP to the letter. When cameras cover the area, operators also check them through remote video monitoring.

A Sirix operator at a command center workstation, with an alarm open on the Sirix Operation Center screen

01

The sensor raises a tamper alert

Covered, moved, struck or disconnected. The alert reaches the Sirix command center with the exact location and the type of tampering.

02

An operator takes it right away

A live Sirix operator responds immediately. No alert waits in an inbox or on a phone nobody is watching.

03

The operator follows your SOP

Your SOP sets the actions and their order. Depending on your site, the operator can open nearby cameras, use voice intervention through a connected speaker, call keyholders or the building manager, dispatch guards or call the police.

04

Your coverage gets restored

The operator notifies your designated contact that the sensor needs to be checked and put back in service, and documents the event. Your coverage gets restored, not just reported.

A sensor knows it was touched. A live operator makes sure someone does something about it.

With or without cameras. With or without speakers.

Sirix follows each site’s SOP and needs. Cameras and speakers add options, never conditions.

With a camera nearby

The operator opens it and sees who is near the sensor, whether they are still there and whether anything else is happening.

With a connected speaker

The operator can speak to the person on the spot. Hearing a live voice usually ends the tampering in seconds.

With neither

The operator still acts on your SOP right away: keyholders, the building manager, guards or police. The task leaves your team’s hands either way.

What a tamper alert does alone, and what tamper detection monitoring adds

Tamper alert alone compared with tamper detection monitoring by Sirix
A tamper alert aloneTamper detection monitoring with Sirix
Detects covering, moving and impactsDetects covering, moving and impacts
Sounds a siren in the roomSends the alert to a 24/7 command center
Sends a text or email someone has to seeA live operator takes it, day or night
Staff guess what to doOperators follow your SOP to the letter
Nobody sees who did itOperators check nearby cameras, when available
Nobody speaks to the personVoice intervention through a connected speaker, when available
The sensor can stay out of service for daysYour contact is told to put it back in service
A line in a logA documented event

Beyond sensors

Tamper alerts from any connected device

Tampering is not limited to ceiling sensors. Sirix supports 500+ manufacturers, so tamper and trouble alerts from cameras, alarm systems and other connected devices can reach the same live operators and the same SOP.

Cameras

A camera can be covered, spray painted, pushed off its view or knocked out of focus. Camera analytics flag it, and a live operator checks what happened. Camera alerts are not always real: according to camera manufacturer documentation, a sharp lighting change, such as a light being switched off, can trigger a tampering alert. That is why a person verifies before anyone is dispatched. For ongoing camera health, see Camhealth.

Car dealerships and construction sites

On open lots and job sites, cameras and equipment are the target, often at night. Tamper alerts reach an operator who responds on your SOP, alongside alarm video verification. Explore construction site security and automotive dealership security.

Outdoor security camera on a wall at a construction site at dusk, its lens covered in black spray paint

Compatibility is confirmed during your site assessment.

Simple to deploy and support

Easy to set up. Easier to live with.

Sirix oversees the rollout, handling the configuration and every connection to our command center. Choose monitoring and the extra steps are ours too.

Your existing sensor

Vape, smoke or safety sensor, with tamper detection built in

Your network

Alerts travel over your existing connection

Secure link to Sirix

An encrypted connection from your site to our command center

Sirix command center

Live operators respond, 24/7

Included in every plan

Our configuration and tamper sensitivity tuning, and tamper alerts on your own platform.

Added when Sirix monitors

The secure link to our command center, live operator response on your SOP, plus any linked camera and speaker.

We configure everything.

Tamper sensitivity, alert rules, schedules and escalation contacts are set up by Sirix and tuned to each space, so normal cleaning and maintenance do not flood you with alerts.

Cameras and speakers, handled.

If a linked camera or a speaker is part of your SOP, Sirix connects it to the command center and confirms that it works.

We guide every step.

From assessment to go live, a Sirix team leads the rollout, so you are never left figuring it out alone.

24/7 support team.

If anything goes wrong at any point, our team is on it around the clock to fix it fast and keep your coverage live.

Works with the sensors and systems you already run

Sirix is sensor agnostic, with 500+ manufacturers supported. It connects tamper alerts from multisensor brands such as HALO and Triton, along with the cameras and video management systems you already use. Not sure which sensor fits your spaces? One call to Sirix is all it takes.

Compatibility is confirmed during your site assessment.

Simple pricing

How much does tamper detection monitoring cost?

Tamper detection monitoring services in North America generally fall between $10 and $75 per device per month, depending on the services required. Run alerts on your own platform, or hand every tamper alert to our operators.

Self-serve

from $10 per device / month

Alerts on your platform.

Recommended

Fully monitored

from $75 per device / month

Verified and acted on by our operators.

Prices shown are North American market estimates for monitored sensor services, not a Sirix price list. Final pricing is set during your site assessment.

Our operator promise

Every alert reaches a real person

Bilingual Sirix operators answer every alert the moment it comes in, around the clock. No alert waits for business hours, and every alert is answered by a trained operator.

100%

of alerts answered by a live Sirix operator

24/7

every day of the year, alerts never wait for office hours

Never

a robot or an answering machine, always a trained operator

10+ years in business, with a redundant backup center.

Sirix never discloses the sites it protects. Confidentiality is part of the service, so you will not find site names or the organizations we protect listed here. What we can show you is the operation behind the promise: the command center behind this service already monitors 25,000+ devices across 230+ cities in the USA and Canada.

Two Sirix operators at work in the Sirix command center, with the Sirix logo on the video wall

Privacy by design

Protection without surveillance

Tamper detection watches the device, not the people in the room. The sensors Sirix monitors in private spaces have no camera and record no video or audio, so protecting them never means surveilling anyone.

Capabilities and certifications vary by model and are confirmed during your site assessment.

A small round white sensor on a white ceiling, with no camera or lens

Where it works

Built for the spaces where sensors get targeted

Sensors get covered and knocked down wherever someone wants to do something unseen. Sirix operators respond for every industry below.

School restroom with sinks and stalls, a small sensor on the ceiling

Schools and campuses

Shared amenity room in a condo building in the evening, a small sensor on the ceiling

Condos and multifamily

Back hallway of a store leading to the customer restrooms, with a small sensor on the ceiling

Retail and quick service

Office floor corridor after hours, leading to the shared restrooms, a small sensor on the ceiling

Commercial and offices

Quiet hotel corridor outside guest rooms in soft evening light, a small sensor on the ceiling

Hotels and hospitality

Also used in healthcare and senior living, libraries and municipal buildings.

What is at stake

A covered sensor is a blind spot nobody sees

Sensors get covered with tape or plastic wrap, knocked off their mounts and unplugged, often by the very people they are meant to deter. Each one is an investment: vape and safety sensors in school restrooms cost about $1,000 each, as reported by KUOW, an NPR member station. An alert nobody acts on leaves both the space and the device unprotected.

Lost coverage

A covered sensor detects nothing. Until someone notices, the space is as unprotected as if the sensor was never there.

Lost equipment

A sensor pulled down or broken is a replacement cost. A fast response often stops the damage before it is done.

False alarms

Not every tamper alert is real. According to Triton’s own documentation, with sensitivity set too high, a sensor’s own speaker can trigger one. A live operator tells the difference before anyone is dispatched.

Staff workload

Your team cannot answer a siren at 2 a.m. Sirix operators carry that load so your people stay on their real work.

Tamper signals at a glance

Common tamper signals and how a Sirix operator responds
SignalWhat usually causes itWhat the sensor reportsWhat a Sirix operator does
Covered or blockedTape, plastic wrap, a cup or a bag over the sensorA covered or masked alertChecks nearby cameras if any, follows your SOP, notifies your contact to clear it
Moved or removedPulled off the ceiling or wall, turned on its mountA movement or removal alertFollows your SOP, notifies your contact to remount it
Struck or shakenHit with an object, kicked or knockedAn impact alert, often with a local alarmSpeaks through a connected speaker if any, follows your SOP
DisconnectedUnplugged or cable cutA disconnect alert, depending on the modelFollows your SOP, notifies your contact to reconnect it
False triggerThe sensor's own speaker, cleaning or maintenance workA tamper alert with no real threatChecks what it can before escalating, so nobody is dispatched for nothing

One sensor, many possibilities

More than tamper detection

Tamper detection keeps your sensors on duty. What they are installed to detect, from vaping to aggression, can reach a live Sirix operator too. Explore the monitored services Sirix offers.

Vape detection monitoring

Vape aerosol, THC oil and masking sprays in the spaces cameras cannot watch, verified and acted on by operators.

Air quality monitoring

CO2, carbon monoxide, particulates and VOCs tracked room by room, with a live operator behind every alarm.

Panic button monitoring

A spoken safeword or a panic button sends a silent alert, and a live operator sends help.

Restroom loitering sensor monitoring

Flags when someone stays too long or stops moving, so a medical emergency gets a response in time.

Smoke and nicotine monitoring

Cigarette and cannabis smoke, nicotine and the sprays used to mask them, verified and acted on by operators.

Temperature and humidity monitoring

Temperature, humidity and energy conditions tracked in real time, so unsafe rooms surface early and you cut wasted energy.

Gunshot detection monitoring

360-degree gunshot detection with dual authentication, so a confirmed shot reaches operators in seconds.

Aggression and noise monitoring

Raised voices, fighting, glass break and screams, so a conflict gets a response before it becomes an injury.

Spoken keyword monitoring

Keywords detected as they are spoken, with no audio recorded, so a call for help reaches an operator fast.

Occupancy and people counting

Overcrowding and after-hours presence flagged automatically, so you stay ahead of capacity and access limits.

Cellphone detection monitoring

Detects phone use in restricted areas, even burner phones, so policy holds where supervision is hardest.

Motion detection monitoring

Detects movement in spaces that should be empty, so after-hours activity and trespassing reach an operator right away.

Works alongside

Camhealth

Ongoing health checks for your cameras, so a camera that goes dark gets noticed.

Alarm video verification

Video confirmation of any alarm before and during dispatch.

Voice interventions

Live announcements through site speakers when your SOP calls for it.

Continuous monitoring

Live operators watching your camera feeds on any schedule you choose.

Security integrator? Offer monitored tamper detection to your clients, behind your brand.  Become a partner

Get started

Put a live operator behind every sensor

Tell us about your spaces and the sensors you have, or plan to have. We design the monitored tamper detection plan around your real risks and your SOP.

Required fields are marked with an asterisk

A Sirix specialist will contact you within one business day.

Prefer to talk? Call 1-855-788-1919 or email info@sirixmonitoring.com.

By submitting this form you agree that Sirix may contact you about tamper detection monitoring. See our privacy policy.

Answered by a real person, 24/7

Tamper detection monitoring, answered

What is tamper detection monitoring?

Tamper detection monitoring connects the tamper alerts built into sensors and security devices to a 24/7 command center. When a sensor is covered, moved, struck or disconnected, a live Sirix operator receives the alert and responds on the site’s protocol, with or without cameras or speakers, across the US and Canada.

Depending on the model, a tamper alert detects when the sensor is covered or blocked, turned or pulled off its mount, hit or shaken, or disconnected. Many sensors use an internal motion sensor to know their normal position, and some also sound a loud alarm on the spot.

The alert reaches the Sirix command center with the location and the type of tampering. A live operator follows the site’s SOP, which sets the actions and their order. That can mean opening nearby cameras, speaking through a connected speaker, calling keyholders or the building manager, dispatching guards or calling the police. The operator also notifies the site’s contact to put the sensor back in service.

No. Cameras and speakers are options, never requirements. With a camera nearby, the operator sees what is happening. With a connected speaker, the operator can speak to the person. With neither, the operator still acts on the site’s SOP right away.

Tamper detection is a sensor feature: the device notices it was touched and sounds a siren or sends a text. Tamper detection monitoring adds what happens next: a live Sirix operator receives the alert 24/7, follows the site’s SOP and makes sure the sensor is put back in service. The sensor detects; the monitoring service responds.

Sirix is sensor agnostic. It connects tamper alerts from HALO, Triton and other major manufacturers to its 24/7 command center, with 500+ manufacturers supported. Not sure which sensor fits your spaces? One call to Sirix is all it takes. We recommend the right sensor for your spaces and budget, then coordinate every step until your coverage is live.

Depending on the model, many sensors report when they are disconnected, and that alert reaches a Sirix operator like any other tamper alert. Device health monitoring is part of the fully monitored plan, and a Sirix specialist can explain how it works for your sensors.

The most common tricks are covering the sensor with tape, plastic wrap or a bag, knocking it off its mount, hitting it, or unplugging it. Built-in tamper detection catches these attempts. With Sirix, each one reaches a live operator who responds on the site’s SOP instead of a siren nobody answers.

They happen. Cleaning, maintenance work or a sensor’s own speaker with sensitivity set too high can trigger a tamper alert. Sirix tunes tamper sensitivity for each space, and a live operator checks what it can before escalating, so nobody is dispatched for nothing.

Tamper detection monitoring services in North America generally fall between $10 and $75 per device per month, depending on the services required. Self-serve, where alerts arrive on your own platform, starts from $10. Fully monitored, where live operators respond on your SOP, starts from $75. These are market estimates, not a Sirix price list, and final pricing is set during the site assessment.

The sensors Sirix monitors in private spaces have no camera and record no video or audio. Tamper detection watches the device itself, not the people in the room. Exact capabilities vary by model and are confirmed during the site assessment.

Yes. Sirix supports 500+ manufacturers, so tamper alerts from cameras that are covered, spray painted or pushed off their view can reach the same operators. For ongoing camera health checks, Sirix offers Camhealth.

A tamper alert reaches the Sirix command center within seconds, and a live operator takes it right away, day or night, following the site’s escalation plan.

Schools and campuses use it most, followed by condos and multifamily buildings, retail and quick service stores, office buildings and hotels. Healthcare and senior living, libraries and municipal buildings use it too. Car dealerships and construction sites rely on it for cameras and other equipment.

The site’s SOP decides. Typically the operator notifies the designated contact, such as the facility manager, building manager or school administrator, and calls keyholders, guards or police when the situation calls for it. Every event is documented.

Yes. Sirix is a wholesale monitoring provider and works only through security integrators and installers. You sell and install the sensors, and Sirix operators take every tamper alert 24/7, behind your brand. Sirix does not sell to end users and never competes with you for your clients. See how to become a partner.

Keep every sensor on duty, around the clock

Many of the vape, smoke and safety sensors you already have can also flag tampering. Sirix responds and gets your coverage back. Let’s design the monitored plan for your spaces.

A Sirix operator on duty at a workstation in the Sirix command center, with other operators in the background